Pentek, Inc., today released its highest-performing D/A converter module for RF and IF waveform playback, the Cobalt® Model 71671. The module delivers four independent analog outputs each through its own digital upconverter and 16-bit D/A with sampling rates to 1.25 GHz. An on-board Xilinx Virtex-6 FPGA contains factory-installed intellectual property (IP) that provides turnkey waveform generation for output signal bandwidths from less than 1 kHz up to 250 MHz with an extended interpolation range from 2x to 1,048,576x. Users can also customize the module’s operation by implementing their own IP in the FPGA.
The Model 71671 uses two DAC3484 D/A converters from Texas Instruments (TI), each providing two digital upconverters (DUCs) and 16-bit D/A channels that can translate a quadrature (I+Q) baseband signal to a user-selectable IF (intermediate frequency) center for transmitting.
Complementary synchronizer products can deliver clock and timing signals to multiple 71671 modules for synchronizing, triggering and gating functions. Synchronization is essential for multichannel applications such as phased array radars and beamformed communications antennas. These applications abound in government and military systems, but the same beamforming concepts are also used in medical and industrial systems.
“The built-in IP for extended interpolation allows customers to handle an extremely wide range of transmit signal bandwidths,” noted Rodger Hosking, vice president of Pentek. “Because the DAC3484 provides a maximum interpolation of only 16x, it accommodates input transmit signal bandwidths from 250 MHz down to 62.5 MHz. However, many radar and communication signals need to generate IF signals with much lower bandwidths. By extending the interpolation to 1,048,576x, the Model 71671 now supports input signal bandwidths as low as
850 Hz, while still covering maximum bandwidths up to 250 MHz, making it a perfect complement to our family of Cobalt A/D converter modules with built-in digital downconverters.”
Precision Timing Enables Large Synchronous Systems
The Model 71671’s internal clock generator supports a wide range of timing modes and operates from an on-board programmable voltage controlled oscillators (VCXO) or an external clock. A front-panel connector accepts a 5 or 10 MHz reference clock to phase lock the internal programmable VCXO. The module also accepts a direct D/A sample clock input.
To offer precision timing control in a multi-module design, Pentek has implemented its new µSync timing bus in the Model 71671. The bus uses current-mode logic (CML) signaling for highest precision and includes clock, sync/reset and gate/trigger signals that keep the operations of multiple modules sample-synchronized. The Model 7192 and 9192 Synchronizers can drive up to 12 modules.
High-Performance I/O
The Model 71671 complies with the VITA 42.0 XMC interface specification, providing two gigabit serial connectors. The primary XMC connector supports x4 or x8 PCIe Gen 2 with multiple DMA controllers for efficient transfers to and from the module. The secondary connector supports two 4x or one 8x link with bit rates up to 3.125 GHz to support user-installed gigabit serial protocols such as Aurora, Serial RapidIO, or a secondary PCIe interface. An additional I/O option provides 20 low-voltage differential signaling (LVDS) differential pairs to the FPGA through the PMC P14 connector.
Built-in and Customizable Operation
Like all Cobalt family modules, the Model 71671 includes a Xilinx Virtex-6 FPGA to implement internal data flow. The FPGA factory-configured functions include a sophisticated Waveform Playback IP module with four linked-list DMA controllers to support waveform generation from tables in either on-board or host memory. Up to 64 individual link entries are available for each channel and they can be chained together to create complex waveforms with a minimum of programming.
Pentek also provides users with its GateFlow® software development tool for implementing custom IP in the FPGA. The tool includes source code for the factory-implemented configuration as well as other system IP, allowing users to customize the module’s default operation as well as incorporate proprietary IP. Customers can also choose the size of the FPGA on their module, ensuring they will have adequate capacity for implementing the functionality they desire.
Pricing and Availability
For the latest pricing and availability information, please contact Mario Schiavone by phone at (201) 818-5900 ext.229, or by email at [email protected].
About Pentek
Pentek develops, manufactures and markets innovative DSP systems and recorders to original equipment manufacturers, distributors and value-added resellers. Pentek offers powerful VME, VPX, VXS, PMC, XMC, cPCI, PCI, PCIe and AMC boards for data acquisition, software radio and digital signal processing featuring Texas Instruments C6000 DSPs, Freescale G4 PowerPCs and Xilinx FPGAs. Pentek’s I/O includes A/Ds, D/As, FPGAs, digital up/downconverters and more. Pentek equips all products with high-performance I/O including gigabit serial interfaces and offers strong DSP software support.